E-Flite Mini Ultra Stick

E-Flite Mini Ultra Stick Key Features

• Perfect transitional airplane for advancing pilots who want to learn aerobatics and for sport flyers who want easy comfortable sport flyer
• Design based on Hangar 9’s popular line of Ultra Sticks
• Lightweight balsa and ply construction
• Covered in genuine Hangar 9 UltraCote
• Two firewall options let you use a wide variety of motor sizes, types and brands
• Includes molded firewall stick mount
• Optional quad-flap configuration
• Tough, lightweight aluminum landing gear that’s pre-assembled and tall enough to accommodate larger prop sizes
• 95% pre-built—get flying in 2 hours or less
• Control surfaces have pre-installed hinges and control horns
• Bolt-on tail requires no gluing and secures with two lock nuts
• Great match for E-flite Park 450 Outrunner Brushless Motor
• Easy access top battery hatch

Mini Ultra Stick Overview

Based on the popular Hangar 9 Ultra Stick, the E-flite Mini Ultra Stick comes 95% prebuilt from balsa and light-ply and is covered in genuine UltraCote. At the heart of the Mini Ultra Stick’s fun factor are two firewall options that let you use a wide variety of motor sizes, types and brands. This along with the ample clearance for larger props that its tall, lightweight aluminum landing gear provides gives the Mini Ultra Stick huge performance potential. You can push the envelope even further by adding the optional split quad-flaps.

Mini Ultra Stick Specifications:

• Wing Span: 38.75 in (985mm)
• Overall Length: 34 in (865mm)
• Wing Area: 325 sq in (21 sq dm)
• Flying Weight: 22 - 25 oz (625 - 710g)
• Motor Size: Park 400 Inrunner or Park 450 Outrunner
• Radio: 4-channel or greater (7-channel for quad flaps)
• Servos: 4 sub-micros (6 sub-micros for quad flaps)
• Trim Scheme Colors: UltraCote Fluourescent Blue, Flame Red,
• Transparent Red & White
• CG (center of gravity): 2.25 in (57mm) behind the leading edge
• Prop Size: 10x7 - 11x7
• Hardware Included: Yes
• Speed Control : 20A Brushless
• Recommended Battery: 2100 mAh 3-Cell 11.1V Li-Po
• Flaps: Yes (optional)
• Control Throw (Ailerons): 1/2 in (15mm) Up/Down Low Rate or 5/8 in (19mm) High Rate
• Control Throw (Elevator): 9/16 in (18mm) Up/Down Low Rate or 7/8 in (23mm) High Rate
• Control Throw (Rudder): 7/8 in (23mm) Right/Left Low Rate or 1-1/4 in (32mm) High Rate
• Approx. Flying Duration: 10-20 minutes
• Scale: Park Flyer
• Approx. Assembly Time: 1-2 hours
• Gear Ratio: 6.5:1 when using Park 400 Brushless Inrunner

Detailed Information

The Mini Ultra Stick can be assembled and ready for flight in just 1 to 2 hours thanks, to:

• Preinstalled control surfaces and hinges
• Preinstalled control horns
• Preinstalled pushrods
• Bolt-on horizontal and vertical stabilizers
• Preassembled landing gear with wheels attached

Mini Ultra Stick ARF Bulletins

You must use a separate BEC or an onboard receiver battery pack when utilizing the quad flap option due to the higher number of servos used in the aircraft and higher current load. Brushless speed controls are not rated to handle more than four servos under load. Please consult the brushless speed control instructions for details and how to disable the BEC on your speed control.

For your convenience, the Mini Ultra Stick features pre-installed pushrod tubes. If you are experiencing any issue with the pushrods sticking and do not have a free movement of the rods, please use an X-acto to open up the ends of the tubes. The tubes were cut at the factory at are rough and in some cases crimped from the cutting process. You should check this when you install your pushrods.

Mini Ultra Stick ARF Team Tips

Two Firewall Options

Optimize the Mini Ultra Stick for use with outrunner or inrunner geared motors with one of two firewalls that are included. A molded bulkhead stick mount is also included, allowing you to use any of the most popular motor sizes and brands available.

Bolt-on Tail and Wing

Two hex screws hold the wing firmly in place and make it easy to access the elevator and rudder servos, as well as the receiver. The tail is secured with two heavy-duty lock nuts.

Quad Flap Conversion

Pilots can push the Mini Ultra Stick’s flight envelope even further with the optional split, quad-flap configuration. The wing includes extra servo trays and special aileron construction that makes converting to this configuration quick and easy. A 7-channel radio and receiver with servo reversing capability is required along with some additional servo extentions for this option.

You must use a separate BEC or receiver battery since brushless esc typically cannot handle the current load of more than four servos.

Power Setup Overview

The Mini Ultra Stick is versatile enough to accommodate a wide variety of motor choices. E-flite’s Park 450 890Kv Brushless Outrunner Motor (EFLM1400) with Outrunner Stick Mount (EFLM1915) provides excellent aerobatic or sport performance when matched with a 10 x 7 prop (EFLP1070). For a high power geared alternative, try the E-flite Park 400 4200Kv Brushless Inrunner Motor (EFLM1100) with a 6.5:1 gearbox (EFLM240) and 11 x 7 prop (EFLP1170).

Spektrum DX6 2.4GHz DSM Radio

The Mini Ultra Stick requires a 4-channel transmitter (7-channel w/mixing for quad flap option) and micro receiver. We recommend the crystal-free, interference-free Spektrum DX6 2.4GHz DSM System, which includes a micro receiver and 4 sub-micro servos.

	Download E-Flite Mini Ultra Stick Manual     E-Flite's Mini Ultra Stick - Extremely Versatile and An Absolute Blast to Fly - Ideal for those making the transition from electric trainers, or any RC pilot looking for a spirited sport plane that goes together fast.